tag:blogger.com,1999:blog-685140657992635767.post3377172405580733943..comments2024-02-16T03:06:37.522-05:00Comments on The Bois Shop: Stacking the oddsRob Boishttp://www.blogger.com/profile/10035998896364908864noreply@blogger.comBlogger7125tag:blogger.com,1999:blog-685140657992635767.post-11261286915380693702013-02-09T14:17:51.135-05:002013-02-09T14:17:51.135-05:00Sorry Jim, but I think it's going to be anothe...Sorry Jim, but I think it's going to be another 2 episodes before I reveal the secret to the joinery. Oh, and because this wasn't enough of a challenge, I decided to add some hidden drawers as well. What was I thinking?Rob Boishttps://www.blogger.com/profile/10035998896364908864noreply@blogger.comtag:blogger.com,1999:blog-685140657992635767.post-2148762634141029922013-02-08T22:56:50.575-05:002013-02-08T22:56:50.575-05:00Rob,
I've laid awake for three nights trying ...Rob,<br /><br />I've laid awake for three nights trying to figure out how you are going to get slip tenons into that double compound angle on a curved piece. This morning in the shower it finally hit me. <br /><br />Give up. Use that beautiful piece of walnut for a jewelry box. That's what I would do. <br /><br />Yes, I am the guy who begged you to use the walnut for a sideboard, but I didn't think you'd actually try it. Man, you either have some serious skills or a serious pair (or both). Seriously, great work, guy. <br /><br />JimJim Ahttps://www.blogger.com/profile/00413818984489791275noreply@blogger.comtag:blogger.com,1999:blog-685140657992635767.post-58443998507742080402013-02-07T16:17:37.868-05:002013-02-07T16:17:37.868-05:00Rob:
I will be at the Furniture Project probably ...Rob:<br /><br />I will be at the Furniture Project probably Friday afternoon. I can sneak over after work. I work in the Design Center Building so I could walk there if I wanted. I went last year and it was great. <br /><br />Thanks again for all the videos. I'll be downloading a few to the tablet to watch if the power goes out during this big snow we got coming.Anonymoushttps://www.blogger.com/profile/07221154766070056999noreply@blogger.comtag:blogger.com,1999:blog-685140657992635767.post-16852503019174216472013-02-06T14:41:15.403-05:002013-02-06T14:41:15.403-05:00Thanks Adam, I appreciate the kind words. Just as ...Thanks Adam, I appreciate the kind words. Just as a word of caution, if you dive too deep in the archives, you may find the lighting, audio, and editing a bit more challenged ;)<br /><br />Also, since you're in the Bay State, if you get a chance you should drop by the Furniture Project during the New England Home Show. I'll be exhibiting this very piece at the show. Details are here: http://designbuildshow.com/Rob Boishttps://www.blogger.com/profile/10035998896364908864noreply@blogger.comtag:blogger.com,1999:blog-685140657992635767.post-63330280248644843562013-02-06T04:56:15.901-05:002013-02-06T04:56:15.901-05:00Rob:
I just found your blog thru a re-tweet from ...Rob:<br /><br />I just found your blog thru a re-tweet from MWA. Thanks for putting this out there. Your videos are well done with good lighting, audio and editing. Your hosting style is relaxed as well. I'll definitely be diving into the back videos. <br /><br />BTW, I also live in the Commonwealth, nice to see a local guy!Anonymoushttps://www.blogger.com/profile/07221154766070056999noreply@blogger.comtag:blogger.com,1999:blog-685140657992635767.post-61002556248430277972013-01-31T17:21:19.164-05:002013-01-31T17:21:19.164-05:00Unlike a stacked lamination or steam bending, a be...Unlike a stacked lamination or steam bending, a bent laminated curve remains in tension indefinitely. It is only those glue lines that are holding the laminates from slipping and unbending. So as a general rule, I don't like cutting much joinery into a bent lamination. Every time you cut through a glue line, there is the opportunity for the piece to "unbend" slightly. Now at the ends for something like a tenon you should still be fine since the only part that could come out of bend is the tenon itself (not a problem). But in my case I am doing fairly long floating tenons, so I would be removing quite a bit of "glue line" surface inside the apron. So I don't think you run any real risk cutting tenons on the end, but those bridal joints really make me nervous. They are cut right in the middle of the bend severing probably two or three glue lines across the entire span. I think the piece in the video shows some "spokes" inside the table that probably help keep the bend after assembly. But the mating leg in the bridal joint won't do anything to shore up those severed glue lines even after they are glued up. Consider an extreme example where there are only three laminates in that bent piece and the bridal joint cuts completely through the outer two. The bend would spring back completely straight at the bridal joints. Obviously those bridal joints don't cut that deep but they must sever at least one or two glue lines on each side.Rob Boishttps://www.blogger.com/profile/10035998896364908864noreply@blogger.comtag:blogger.com,1999:blog-685140657992635767.post-33345618358462998532013-01-31T16:06:03.699-05:002013-01-31T16:06:03.699-05:00Hey Rob can you elaborate more on your reasoning f...Hey Rob can you elaborate more on your reasoning for not using bent lamination. I'm looking to incorporate a curved front into a project and was planning to use bent lamination for the apron that will have tenons cut into the ends along with bridal joints in the middle. Similar to this project:<br />http://www.youtube.com/watch?v=xfxgouMvAgo&list=UUjatELwdjLj3_03Q80iTc_g&index=13<br />I've never done this before, but I would think that if the laminated glue bond is compromised by cutting joinery into the lamination that it would regain its strength once the joint comes together. I know I'm missing something here, so any light you can shed would be greatly appreciated.Anonymousnoreply@blogger.com